Snap-Loc Clip for Trex Decking

$164.45

Trex Decking Klevaklip Snap-Loc Clips

Box of 40 Clips

Klevaklip Building Supplies Online

x
Trex Decking AustraliaKlevaklip Building Supplies

Description

Snap-LOC Clip for TREX® Transcend Decking

USA PATENT – 10577807   AUSTRALIAN PATENT PENDING 
The KlevaKlip Snap-Loc clip for Trex® decking is approved for use with Trex ® registered trademark boards in Australia.

 

Whilst Trex® decking has for quite some time had a groove in the side of the board to allow a “biscuit-type” fixing to be used to hold down the boards, biscuit clips tend to be quite fiddly due to having to fit the “biscuit” into the groove in the board and the drive a very small headed screw in between the boards. It is a two-part process as the screws cannot be fully tightened until the following board is laid. Moving from joist to joist fitting and tightening clips is certainly no slower than conventional screwing down of a decking board, but it is tedious, hot work. There must be a better way……..

ENTER THE KLEVAKLIP

KlevaKlip has been supplying fixed pitch, continuous clipping systems into the Australian decking market for over ten years, with many millions of clips having been installed on decks.

Our new clip, manufactured from High Quality Engineered Impact Modified Nylon, for Trex® Transcend decking, is two to three times faster to install than conventional “biscuit-type” decking clips.

For the decking contractor this means you can quickly get the job finished and move onto the next job, whilst for the DIY-er, your time to sit back and enjoy your first beer on the deck is ever so closer.

 

PLEASE NOTE: Klevaklip Snap-Loc Clips for Trex Decking are NOT suitable for non-square or irregular shaped decks. For non-square decks it is recommended to use the Trex Connector Clips.

 

Trex Decking Snap Loc Clips Klevaklip

Trex Decking Snap Loc Clips Klevaklip

 

Q1. How many Snap-Loc Clips do I get in a box?

There are 40 units per box supplied.

One box of 40 Snap Loc Clips for Trex Decking covers approximately 10m2 (Based on 450mm joist centres)

 

Q2. What screws do I require?

The Klevaklip Snap-Loc Clips for Trex Decking recommends that you use Galvanised 8 gauge button head screw (head size less than 2mm) on a timber substrate.

On a metal substrate it is recommended to use a 10 gauge x 16mm wafer head screw.

NOTE: Screws are NOT supplied with your Klevaklip Snap-Loc Clips for Trex Decking

 

Q3. How many screws will I require?

The Trex Decking Klevaklip Snap-Loc Clips require 8 screws per clip (320 screws per box)

 

Q4. Do I require an adhesive for installation of the Snap-Loc clips for Trex Decking?

Klevaklip highly recommend the use of adhesive products in their installation guide. It is recommended to use any MS, SMX or Polyurethane based outdoor adhesive product.

Please refer to the Trex Decking Klevaklip Snap-Loc Clips installation guide to view this recommendation.  You can download this here:

Trex Decking Snap Loc Clips Klevaklip Installation Guide

 

 

Brand

Trex Decking

Trex Decking Australia

Klevaklip Building Products

Klevaklip Building Supplies

Additional information

Weight 25 kg
Dimensions 50 × 30 × 20 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.