Cutek Restore (Proclean)

$60.50 - $192.50

Cutek Restore (ProClean)

Features of Cutek Restore (ProClean)

• Professional Grade Clean – Keeps working deeply for up to 24 hours
• Removes many types of stubborn stains including iron, tannin and water stains
• Restores timber and enhances grain

SKU: CUTEK-R Category:


Cutek Restore (ProClean)

Want to revive your deck or cladding that has greyed off? Need to know how to restore decks, cladding and screens?

The solution is Cutek Restore (ProClean). This professional grade wood restoration cleaner will brighten, clean and restore wood to look like new, ready for coating with Cutek oils.

Use when timber is significantly grey and weathered, or to remove stubborn stains caused by tannin, iron, water, resin, mould & fungus etc.

Always patch test Restore (ProClean) before use.

  • Professional grade wood restoration cleaner that keeps working for up to 24 hours.
  • Removes stubborn stains, including iron and water stains
  • Restores oxidized and grey timber while enhancing the grain

Unlike bleach, Cutek Restore (ProClean) is not considered a strong defoliant, however, we recommend using absorbent drop cloths to protect delicate and/or adjacent vegetation and surfaces.

For best results use Cutek Restore (ProClean) as supplied and stir it well before use. Sometimes, if you’re working with an easy to clean surface Cutek Restore (ProClean) can be diluted with water. If a choice to dilute the product is made, always test to determine if the dilution being used is effective in cleaning.


Before you begin, note the hazards and precautions on this website and the can labelling, and ensure that you use the correct safety equipment as detailed in the Safety Data Sheet.

After testing a patch of timber and determining the required dilution, if any, apply Cutek Restore (ProClean) liberally to a pre-wetted timber substrate with brush, roller, or garden sprayer.

Let Cutek Proclean do most of the work by letting it sit on the surface for 10 minutes – 8 hours, or such time as deemed to be necessary by the test procedure. It may be necessary to scrub stubborn stains moderately with a stiff fibre brush.


Once Cutek Restore (ProClean) has cleaned the timber, it must be power rinsed off thoroughly. For best results, power rinse with a high-pressure washer set to under 750 p.s.i. (50 bar), with a fan jet pattern to avoid damage to the wood fibre.

Clean from the lowest point and work upwards methodically. ALWAYS clean off with a water jet that produces a “putty knife” shaped fan that is 40–50mm wide about 100mm out from jet. Adopt a continuous “mowing action” working with power water fan-jet 100mm from the face of the substrate. DO NOT use “turbojets” on timber. CAUTION must be used when cleaning soft timber to reduce the pressure and avoid damaging the sapwood.

The longer that Cutek Restore (ProClean) is left on the substrate, the greater the rinse time required.

Additionally, certain types of wood surfaces may leave a raised grain effect after stripping is completed. Sanding or poly pad scrubbing may be required to smooth out this condition.

If Cutek Restore (ProClean) is being used to remove mill glaze (a smooth glossy surface found on smooth newly sawn timber, which is impervious to most coatings) use the same procedure as above.

Recoating with a Cutek oil

Following the restoration of the timber with Cutek Restore (ProClean), it is important to complete the restoration process by coating the timber with an appropriate Cutek oil, following the procedures detailed in this website.

Not treating the timber after cleaning will result in the weathering process occurring more rapidly than prior to cleaning.



Additional information

Weight 20 kg
Override Category Fees


Tin Size

10L Tin, 2.5L ProClean (STD), 5L ProClean






There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.